eSnips.com: Atmel AVR

The file 'Avr Assistant' was added by Mike Henning

Sun, 29 Jun 2008 03:59:59 GMT

	Avr Assistant.zip
	Renamed from AvrCalc to avoid a naming conflict with the existing AvrCalc written by Jack Tidwell. Simple Timer / Baud Rate calculator for AVRs. Version 1.3 - Note that the reload value is now given with the proper (value-1). Please feel free to make any suggestions for improvements.

The file 'AvrOspII_547' was added by Mike Henning

Tue, 18 Sep 2007 10:07:16 GMT

	AvrOspII_547.zip
	Added optional BootExit command to the OSPII protocol. Corrected the table jump code for devices with extended memory.

The file 'UniBootloader' was added by Mike Henning

Fri, 29 Dec 2006 01:00:03 GMT

	UniBootloader.zip
	An attempt at making a universal bootloader that will work equally well with all newer Avrs from the Tiny13 to the Mega128. Any suggestions, improvements or bug reports are most welcome!

The file 'Avr-Osp II Screenshot' was added by Mike Henning

Sat, 02 Sep 2006 01:25:28 GMT

	Avr-Osp II Screenshot.png

The file 'AvrOspII_400' was added by Mike Henning

Sat, 02 Sep 2006 01:01:28 GMT

	AvrOspII_400.zip
	GUI Open Source programmer based on Atmels Application note AVR911.

New comment posted on on Sep. 2 2006 by Mike Henning

Sat, 02 Sep 2006 01:14:24 GMT

New/Changed: Version .400

A few cosmetic changes were made

All previous settings can now be restored on startup

Color coded the fuse settings: Yellow = Not verified Green = Verified

In addition, an optional confirmation prompt is given before

programming fuses.

Fixed a bug that would cause the app to exit if a file was specified

that didn't exist.

Fixed a bug that originated in the original AVROSP that incorrectly

reads the last byte if the address is an even number.
(This only existed in ISP Mode)

New comment posted on on Apr. 27 2006 by Mike Henning

Thu, 27 Apr 2006 05:54:46 GMT

New/Changed: Version .360

Fixed the memory fault that would occur if the Devicelist.dat file didn't exist.
If the file is missing a new device file will be built from the current install of Avr Studio.

Fixed a problem with some devices not displaying the AvrStudio style lockbits.

A few a other minor tweaks to syncronize the command line parameters to the new interface.

Invoking AvrOspII with the following parameters will populate the appropriate fields:

AVROSPII -dATtiny2313 -ifmyapp.hex -iemyapp.eep -cCOM2

New comment posted on on Apr. 23 2006 by Mike Henning

Sun, 23 Apr 2006 21:39:07 GMT

New/Changed: Version .350

Added a Copy to clipboard button for the Logbox

Added "Send Exit" button

Enabled the "Auto" button
This will program both Flash and EEPROM as well as the auto options
that are checked.

If either file name is not specified then then the operation will be skipped
for that part of the programming. If both file names are nissing the
entire operation will abort without doing anything.

Added a checkbox to the Auto setting for Send Exit after programming

Operations should abort faster now after receiving a bad response.

New comment posted on on Apr. 23 2006 by Mike Henning

Sun, 23 Apr 2006 02:18:41 GMT

New/Changed: Version .300

Rearranged the GUI a little

Changed the COM timeout back to 5 seconds to rid false timeout warnings
when writing large EEPROMS. I'll make this dynamic in the next version.

Added full support for reading/writing all available Osc. Cal. values.
(Value can be written to EEPROM or Flash)

Added Read Signature.

Added Avr Studio style Fuse and Lockbit settings.

This allows 3 ways to set fuse and lock bits

EZ Avr Studio style
Entering a Hex value
Binary representation

Changing by means of any of the above will automatically update the other to reflect the change.
(Makes a handy interpreter!)

New comment posted on on Apr. 14 2006 by Mike Henning

Fri, 14 Apr 2006 03:47:34 GMT

New/Changed: Version .250

Made programmer id$ case insensitive

Fixed a bug when using blockmode programming
(It works now!) :)

Added a progress bar for reading and writing Flash
(Bootloader mode only at the moment!)